| Author |
 Topic  |
|
peclik
Pulcino
Czech Republic
63 Posts |
 Posted - 27/02/2011 : 00:08:20
|
quote:
But when I tried it with Colibri, LK8000 told that declaration ok, but there were nothing stored on Colibri.
I've checked that and found a bug when sending declaration from PDA/PNA (all names have been sent empty). So 2.1c is wrong, it will be corrected in next version.
Thanks for report.
P.S.: Be prepared that all non-Ascii characters (code >126, i.e. all national ones) will be replaced with '_'. That's for protection of Colibri which is sensitive on some non-Ascii characters. |
Edited by - peclik on 27/02/2011 00:12:07 |
 |
|
|
JefYP
Pulcino
12 Posts |
Posted - 27/02/2011 : 20:04:10
|
In the past on a different project I had the same experience when communicating with LX/Colibri/Posigraph. This was solved with a simple procedure where ü is replaced by u, é by e etc.. If you want this procedure, contact me by email and I'll send it to you.
Kind regards, Jef |
|
|
|
peclik
Pulcino
Czech Republic
63 Posts |
Posted - 27/02/2011 : 23:11:33
|
I think, it's not that easy.
There are many code pages for 8-bit character encoding.
For example in some code page there is 'Ÿ', in the other there's '#269;' (c with wedge) on code 159.
Since LK uses UTF-16 strings, it could be solved using some special UTF-16 to ASCII conversion table.
It could be done, but now I don't care much (many people I know use only ASCII characters in waypoint names). Maybe sometime, if many people will complain about underscores... |
Edited by - peclik on 27/02/2011 23:14:46 |
|
|
|
cyclone
Pulcino
Ukraine
64 Posts |
Posted - 27/02/2011 : 23:23:45
|
Message a low battery on the PNA leads to error message in LK8000. Program crashes.
Also error messages when you exit the program at some PNA.
[That was supposely fixed in 2.1c: are you still using 2.1b??] |
Edited by - Coolwind on 27/02/2011 23:29:25 |
|
|
|
cyclone
Pulcino
Ukraine
64 Posts |
Posted - 03/03/2011 : 08:59:48
|
VERSION 2.1c
|
|
|
|
rkalman
Falchetto
Hungary
175 Posts |
Posted - 03/03/2011 : 13:05:38
|
Yes this crash at program termination is also present on some cheepo chinese pnas. (I also have one that produces this message)
It somehow depends on the pna's rom configuration, however I think nobody have spent time to correct this...
|
|
|
|
Coolwind
Moderator
Italy
8957 Posts |
Posted - 03/03/2011 : 14:03:19
|
| It depends on how you execute LK, also. Only on termination, though. No crash on battery warning. |
|
|
|
cyclone
Pulcino
Ukraine
64 Posts |
Posted - 03/03/2011 : 22:27:55
|
| If the PNA software shell off, the LK does not crash when falling level of the battery. If you do not disable the software shell, then crashes. And not only on Chinese PNA. Tested on the Taiwan PNA, have officially imported to Ukraine. |
|
|
|
cyclone
Pulcino
Ukraine
64 Posts |
Posted - 07/03/2011 : 14:00:39
|
The page Analysis:Task that is displayed in the Task to go?
Comparing different times and could not understand. |
|
|
|
Topic |
|
VERSION 2.1C AVAILABLE