T O P I C R E V I E W |
bambuko |
Posted - 29/05/2018 : 16:11:23 For the fans of Kobo. New HD 6" screen: https://us.kobobooks.com/collections/ereaders/products/kobo-clara-hd
sounds promising...? |
15 L A T E S T R E P L I E S (Newest First) |
bambuko |
Posted - 23/03/2020 : 23:11:05 on my Clara in Device configuration it is: Name- BlueFlyVario Port- /dev/ttymxc0 Baudrate- 115200 8bit |
Andrew Mogg |
Posted - 23/03/2020 : 22:27:18 I am now trying to connect a Bluefly to the Clara. I managed to change the baudrate as mentioned in this post. I connected the tx to rx, rx to tx, GND and VCC. When I turn on the Kobo I am able to turn on the Bluefly, but I cant find the port /dev/ttyACMO. When I enter device set up>device configuration> terminal I get a No Data. What am I missing? Any ideas? |
falchettogiallo |
Posted - 12/03/2020 : 12:19:01 quote: Originally posted by ernst-dieter
Which voltage level is to apply? (3,3V?)
Yes, signals levels are 3,3 |
ernst-dieter |
Posted - 12/03/2020 : 08:10:30 Which voltage level is to apply? (3,3V?) |
ernst-dieter |
Posted - 12/03/2020 : 08:08:06 Thanks ... can not see the appended picture Sorry, seems related to my installation |
falchettogiallo |
Posted - 11/03/2020 : 14:36:45 quote: Originally posted by ernst-dieter
I have already tried the 7.1l-otg-kernel experimentally on the Clara HD. All seems to be fine (handling, graphics etc.) EXCEPT that there is no suitable serial port to connect to. A lot of serial ports are showing up but no one with an attractive name similar to ttyUSB0. A lonely ttymxc0 port can be connected without error but does not transmit anything from my S80. Any hope?
You could connect directly to the ttymxc0 pins on the Clara motherboard. I've done something similar on my Kobo HD and it works like a charm!
|
ernst-dieter |
Posted - 07/03/2020 : 18:21:57 Don't hide your light under a bushel. |
brunotl |
Posted - 07/03/2020 : 17:55:42 i've tried to make a otg kernel but without success, that seems out of my skill... |
ernst-dieter |
Posted - 07/03/2020 : 17:49:33 O.k. Bruno, but not principially ? |
brunotl |
Posted - 07/03/2020 : 17:47:23 USB otg is not supported on Clara HD. sorry. |
ernst-dieter |
Posted - 07/03/2020 : 16:51:52 I have already tried the 7.1l-otg-kernel experimentally on the Clara HD. All seems to be fine (handling, graphics etc.) EXCEPT that there is no suitable serial port to connect to. A lot of serial ports are showing up but no one with an attractive name similar to ttyUSB0. A lonely ttymxc0 port can be connected without error but does not transmit anything from my S80. Any hope?
|
ernst-dieter |
Posted - 07/03/2020 : 16:08:50 Same question ... as my Glow HD is fading out. Clara HD would be the candidate next to |
Andrew Mogg |
Posted - 11/08/2019 : 14:40:49 Has there been any progress on the Clara as far as OTG and/or LKNet goes? |
villamany |
Posted - 15/01/2019 : 14:38:09 Testing a new Clara HD unit and seems to works fine like on the Aura 2ed! On the Clara HD a little better resolution but you need to get booth at the same time for acuse it. Also more free RAM on the Clara.
|
villamany |
Posted - 05/01/2019 : 11:41:53 Thanks, but finally seems to be a defective touch screen. So i will try a new unit. |