| Author |
 Topic  |
|
|
cubiq
Pulcino
12 Posts |
 Posted - 04/06/2012 : 21:42:07
|
Hello,
I've recently bought a Mio M400 to have LK8000 on it.
I unlocked the M400(using the software from the tutorial), installed LK8000, maps, airspaces, etc. I even bought a Condor cable to test. I did some flights on my PC using the Condor cable with no problem.
But when I use it in real life, in my glider, after 10-15 minutes(it's hard to tell exactly) it starts to get blocked from time to time. Initialy it works realy slow and after a while it blocks almose completly. I say "almost" because if I press on the screen I have to wait even 5 minutes to have the action done.
Once I managed to get to exit message box(the one with yes/no) and it took it like a minute only to paint the message box.
The igc is not logged corectly.
Do you have any idea what it could be? I will send the configuration file if it is necesary.
Thanks a lot!
Regards,
Radu. |
|
|
rkalman
Falchetto
Hungary
175 Posts |
Posted - 04/06/2012 : 21:55:26
|
Which version do you use?
Are you using internal flash or microsd card?
Maybe you have a defective card. |
 |
|
|
cubiq
Pulcino
12 Posts |
Posted - 04/06/2012 : 21:59:36
|
Version: 3.0c and it is not an update, it is a new, fresh install.
The M400 doesn't have a card slot but it has "external memory"(1,9GBytes). And I'm using this since the internal memory is very small(64MBytes). |
|
|
|
cubiq
Pulcino
12 Posts |
|
|
Coolwind
Moderator
Italy
7460 Posts |
Posted - 04/06/2012 : 23:42:34
|
The log cannot help. We need the full LK8000 folder of your Mio400, that you should zip and upload somewhere for us. Then we can try to reproduce the problem.
|
|
|
|
cubiq
Pulcino
12 Posts |
|
|
Coolwind
Moderator
Italy
7460 Posts |
Posted - 05/06/2012 : 18:25:48
|
Ok the problem is in the device B , I suppose you are using GT Vario connected to it.
There is a bug in 3.0c in the LK8EX1 driver .
Please wait for 3.2 or use a 3.1 version, this problem is solved there already.
Or, of course, do not connect the GT Vario using 3.0c.
Sorry I thought I had fixed it in 3.0 as well, but it seems I forgot to do it. |
Edited by - Coolwind on 05/06/2012 18:34:39 |
|
|
|
cubiq
Pulcino
12 Posts |
Posted - 05/06/2012 : 18:34:36
|
| Yes I do... The GT Altimeter from GliderTools which is recognized and communicates with the LK8000 very well. |
|
|
|
cubiq
Pulcino
12 Posts |
Posted - 05/06/2012 : 18:43:51
|
Ok, then I'll try the 3.1 version. Thanks for clarifying this. I was about to put a hammer on the device. :)
One more little thing: if I stay with 3.0c version and just remove the altimeter do I have to change the device B to disable or to COM2(GPS port)?
I think I remember that I've read somewhere that if you don't have device B then you should have twice the GPS port? Is it correct?
Thanks a lot! |
|
|
|
Coolwind
Moderator
Italy
7460 Posts |
Posted - 05/06/2012 : 23:28:24
|
| set it to DISABLED, it is simpler in the 3.0 version. |
|
|
| |
Topic |
|
LK8000 stuck on Mio M400